Network Working Group W A Simpson Internet Draft Daydreamer expires in six months June 1993 SIP System Discovery Status of this Memo This memo is the product of the SIP Working Group of the Internet Engineering Task Force (IETF). Comments on this memo should be submitted to the sip@caldera.usc.edu mailing list. Distribution of this memo is unlimited. This document is an Internet Draft. Internet Drafts are working documents of the Internet Engineering Task Force (IETF), its Areas, and its Working Groups. Note that other groups may also distribute working documents as Internet Drafts. Internet Drafts are draft documents valid for a maximum of six months. Internet Drafts may be updated, replaced, or obsoleted by other documents at any time. It is not appropriate to use Internet Drafts as reference material or to cite them other than as a ``working draft'' or ``work in progress.'' Please check the 1id-abstracts.txt listing contained in the internet-drafts Shadow Directories on nic.ddn.mil, nnsc.nsf.net, nic.nordu.net, ftp.nisc.sri.com, or munnari.oz.au to learn the current status of any Internet Draft. Abstract This document specifies ICMP messages for the identification and location of adjacent SIP systems. This is intended to replace ARP, ICMP Router Advertisement, ICMP Redirect, ICMP Information, ICMP Mask, and OSPF Hello in the SIP environment. There are also elements of the OSI ES-IS and IS-IS Hello. Simpson expires in six months [Page i] DRAFT system discovery June 1993 1. Terminology The following terms have a precise meaning when used in this document: system a device that implements the Internet Protocol, IP [9]. intermediate-system a system that forwards datagrams, as specified in [2]. Often called a router or gateway. This does not include systems that, though capable of forwarding, have that capability turned off. Nor does it include systems that do forwarding only as required to obey Source Route options. end-system any system that is not acting as an intermediate-system. Often called a host. dumb the minimal implementation. This is not meant in a perjorative sense. It is intended that every mechanism be defined in such a way that it is implementable on a minimal system. smart an improved implementation, possibly requiring more internal resources, while using less external resources. multicast unless otherwise qualified, means the use of either IP multicast [4] or IP broadcast [6] service. link a communication facility or medium over which systems can communicate at the link layer; that is, the protocol layer immediately below IP. The term "physical network" has sometimes been used (imprecisely) for this. Examples of links are LANs (possibly bridged to other LANs), wide-area store-and-forward networks, satellite channels, and point-to-point circuits. multicast link a link over which IP multicast or IP broadcast service is supported. This includes broadcast media such as LANs and satellite channels, single point-to-point circuits, and some store-and-forward networks such as SMDS networks [8]. interface a system's attachment point to a link. It is possible (though unusual) for a system to have more than one interface to the same link. multicast interface an interface to a multicast link; that is, an interface Simpson expires in six months [Page 1] DRAFT system discovery June 1993 to a link over which IP multicast or IP broadcast service is supported. identifier uniquely identifies each interface; a single interface may have more than one such identifier. primary identifier uniquely identifies each system; only one such identifier is used, to simplify discovery of neighbors. subnet either a single link of a subnetted IP network [7] or a single non-subnetted link. prefix the part of an identifier which may be used for routing to a particular subnet, defined by logically ANDing with its assigned subnet mask. More than one subnet prefix may identify the same link. zone the part of a special identifier which indicates a unique subnet within an administrative domain. neighbor having an identifier belonging to the same subnet. 2. Criteria Historically, the methods for discovery of the next-hop evolved separately from those for location of neighbors and auto- configuration of systems. With the advent of SIP, the old techniques must be re-implemented, usually due to larger field sizes. Unfortunately, older implementations frequently did not take proper care in differentiating existing variable field lengths, version numbers, and new types of messages. Therefore, the techniques used for SIP are required to be distinguishable from previous versions. None of the current protocols are readily extensible. While some have the ability to change in simple terms, such as larger addresses, none were designed to add new kinds of information to be carried in the same packet. This can be viewed is an opportunity to design a uniform and coherent method for accomplishing these goals, rather than a liability. Through prior experience, the following criteria were established, in order of relative importance. It is understood that many of these criteria may conflict, and require numerous tradeoffs. Simpson expires in six months [Page 2] DRAFT system discovery June 1993 Multicast support All SIP systems are required to support multicast. This is the primary technique for distinguishing the new messages. Older systems will ignore multicast messages at the link layer. There are numerous other advantages to using multicast for the new messages. In particular, when compared to broadcast, reduced overhead for processing messages which are not ultimately intended for the local system. Not all media supports multicast. Since multicast is directly supported by the SIP header, this technique will work even when using link-layer broadcast, or link-layer unicast to each recipient. Reduced net traffic Currently, there are separate packets sent for media address resolution, router discovery, and the Hello protocols for the various routing algorithms. Since much of the same information is contained in each of these packets, it would be helpful to combine the functions in a single packet where possible. Also, the most common next-hop resolution protocol, the Address Resolution Protocol (ARP), requires an additional two packets at the beginning of each connection. The Request is sent, a Reply is received, and then the first datagram can be sent to the next-hop. This causes a significant amount of traffic, and considerable latency in establishing a connection. Several alternative methods were proposed: 1) The ISO solution (ES-IS) eliminates some of these problems. Each end-system and intermediate-system sends Hellos on a periodic basis. Every system must remember all of the media addresses for the other systems on the local network. This does eliminate the latency of ARP, at the expense of many additional packets sent on a regular basis, and a large amount of storage overhead in each system. 2) The first packet destined for an unknown system may be sent to the all-systems multicast, or to a media multicast based on a hash function of the destination. The appropriate system accepts the packet, and sends a redirect indicating the appropriate media address to be used for future packets. This reduces the traffic from 3 to 2 packets at the Simpson expires in six months [Page 3] DRAFT system discovery June 1993 beginning of a connection, and eliminates the latency, as the discovery packet sent is also the data packet. The destination identifer in the network header will be unicast, while the media address will be multicast. Intermediate- systems would require extra intelligence to recognize those packets destined beyond the local link, while multi-homed end-systems require that capability already. Also, this method is not extensible to include other information useful in mobile environments. 3) Using advertisements for the (fewer) intermediate systems, and an ARP-like protocol for those end-system connections that are on the local media. For those packets which are clearly destined off the local media, the packet can be sent directly to the appropriate intermediate system. When most of the traffic is between systems that are not on the same local media, this is very efficient. When most of the traffic is between end-systems on the local media (client- server), the extra discovery packets will be rare. The solution that is detailed here is a combination of the best features of the preceding techniques. Intermediate-systems advertise their locations. When an intermediate-system needs the location of an end-system, it requests the location of the end-system, and the end-system replies. Knowledge about end-systems is concentrated in the intermediate-systems, but only for the systems that are actually communicating. End-systems send all datagrams directly to the intermediate- systems. If there is a more direct path to the end-system, because it is directly accessible on the local link or another intermediate-system would be more appropriate, the intermediate- system issues a redirect. Also, by carrying media addresses within the advertisements and redirect packets, a further ARP-like query/response can be avoided entirely. Low storage overhead It is desirable that systems require as little storage overhead as possible. In particular, mobile systems often have significantly reduced processing power and memory. An end-system need only retain information for those end-systems with which it is directly communicating. Simpson expires in six months [Page 4] DRAFT system discovery June 1993 This design requires sufficient storage in an end-system for information about at least one intermediate-system. In addition, storage is required for at least one location of each service (such as a domain name server) which is used. An intermediate-system may require more processing power and memory. Participation in routing protocols requires the knowledge of every neighboring intermediate-system. When subnet prefix-routing is in use, it is not necessary for an intermediate-system to determine the location of an end-system until traffic for the end-system arrives. If prefix-routing is not used, particularly in radio and mobile environments, the location of each reachable end-system must be continuously retained. Auto-configuration It would be highly desirable that the connection procedures for a configuring a new system are reduced to the minimal set of "plug it in, turn on the power, and run". - Each system, or more precisely each interface, should be assigned an identifier, within the number space assigned to the local subnet. - Each system should be assigned a name within the local domain. The name, and the associated identifiers, should be registered in the local domain name server. - The system should discover the external routes provided by the intermediate-systems attached to the local subnet, so that it can exchange packets with remote systems. - The system should discover the location of servers that it needs for configuration, loading, dumping, printing, and other services. In evaluating previous experience with autoconfiguration procedures, the following constraints were determined: 1) It is not possible to embed an IEEE-802 component within every SIP identifier, since the remaining prefix would be too small for global routing. Using the 48-bit IEEE-802 number to identify one system within a local network that is not designed to accomodate more than a few hundred systems is considerable overkill. It may be worthwhile to use the address during initial configuration. Simpson expires in six months [Page 5] DRAFT system discovery June 1993 2) Random identifier assignments are to be avoided. They do not scale well to large networks, are difficult to track and manage, and lead to administrative confusion. Relying on broadcast collision resolution procedures for avoiding duplicate assignments results in conflicts when systems occupy partitioned subnets, or are frequently powered down or taken off-line. 3) Reassignment of identifiers should be transparent to the human users. In particular, renumbering, and assignment of alias identifiers as a mobile system moves should be automatic. 4) End-system users should not be concerned with routing prefixes, or the routing methods extant on the local network. When used, such prefixes should be automatically determined, and dynamic changes should propagate automatically. 5) It is important to allow users to choose a system name which is memorable and comfortable to them. The name should be automatically registered, and changes to the associated identifers should be maintained automatically. This design handles initial self-identification and propagation of changes in identification. Other aspects of configuration, such as loading the operating system and environment, and additional facilities and servers for registration, are specified elsewhere. Mobility support This is sometimes considered a subset of the above, as related to dynamically changing addresses while moving. Other systems must be notified of the changes. In addition, the "hidden transmitter" problem is considered (you can hear another system, it can't hear you, but there is a path to a third system which it can hear, completing the circuit). This is not well supported in any of the past protocols. Although basic support for mobility is provided, descriptions of additional facilities and servers are specified elsewhere. Black hole detection In determining whether the next-hop system is still available, there is a basic tradeoff between frequent queries and resources used. This design trades fewer queries against more information Simpson expires in six months [Page 6] DRAFT system discovery June 1993 within each query and response. Explicit holding times are used to limit the exposure to black holes. The times may be dynamically shortened by the responsible system when a resource is critical, or when the system is actively moving. Media independence There are many instances where system discovery is accomplished differently over different media, such as point-to-point versus broadcast versus Large Public Data Networks. This design places the system discovery above the network layer, where it enjoys greater independence. It also encompasses media level redirects between multiple logical subnets on the same physical media. There are difficulties with carrying media addresses within packets, especially in the presence of multi-media bridges. Rather than allowing translation by bridges in the path, this design exercizes control at the destination system, and requires all such media addresses to be in canonical form, Optimal route determination This is essentially a superset of next-hop discovery, combined with resource reservation and possible policy considerations, and the ability to redirect traffic under changing conditions. This is not well supported in any of the past protocols. To balance system overhead against network traffic, this design attempts to adapt to a continuum of system capabilities. Dumb end-systems may simply send packets to a default intermediate- system, and be redirected to the correct next-hop by more capable intermediate-systems. Smarter end-systems learn sufficient information to make informed choices. Simplicity All of the above desires, and they want to keep it simple, too. This design reduces the number of packet types which must be supported in a pure SIP system, and reduces the number of systems which recognize and respond to each type. The extensions are designed with 32 and 64 bit boundaries for efficient processing. Simpson expires in six months [Page 7] DRAFT system discovery June 1993 3. Design Overview This proposal describes two packets, not much different from those already deployed. These familiar forms are re-packaged to join common functions into the same packet to reduce traffic, and are designed to be more extensible in the future. In order to foster media independence, the packets are part of ICMP, which allows the protocols to be used over broadcast, multicast, partial-mesh, and point-to-point media. This is similar to the positioning of ES-IS. The Where-Are-You solicitation is used to find other systems, and associated resources and services. General solicitations are sent when a system interface is initialized. Specific solicitations are sent when one system is ready to communicate with another particular system. The I-Am-Here advertisement is the answer to the Where-Are-You solicitation. Advertisements are also sent on a periodic basis to indicate special resources and services. Periodic advertisements from a few commonly requested systems result in less traffic than repeated solicitations from many systems. Each advertisement includes a lifetime field, specifying the maximum length of time that the advertisements are to be considered valid in the absence of further advertisements. This ensures that other systems eventually forget about systems that become unreachable, whether that is because the system has failed, or it no longer provides the advertised service. Each message contains "optional" extensions, designed to allow flexibility and extensibility. One of the common extensions is the media address. Each message contains enough information to return a reply directly to the sender, without additional location traffic. Another common extension is a list of the intermediate-systems which have been heard. This allows intermediate-systems to build a map of the paths between intermediate-systems, and between intermediate- systems and end-systems. This is designed to be used by most commonly deployed routing protocols. This also solves the "hidden transmitter" problem, when used together with the well-known link- state class of routing protocols. Several methods of routing are supported. Simpson expires in six months [Page 8] DRAFT system discovery June 1993 3.1. System Identification Zone A Zone is defined to be a collection of links which may be accessed as the same next-hop. A Zone is usually a single link, or a collection of bridged links. When a single intermediate- system is connected to multiple point-to-point links, these links may be collected into a single zone. The Zone number is a fixed size. The value 0 is only used to indicate the local zone. The values 1 through 255 indicate each zone within an administrative domain. Zone numbers may be combined with an interface media address to make a locally significant identifier. This is useful for initial configuration and local communication within the administrative domain. These identifiers may be routed in a similar manner to prefix-routed subnets. The generation of these local identifiers depends upon the availability of a registered unique number, such as an IEEE-802 number. When there is no IEEE-802 number to be found anywhere in the machine, such as when the machine is connected exclusively to point-to-point links, an external link-level mechanism MUST be used to negotiate a unique identifier. Such a mechanism is beyond the scope of this document. Prefix A Prefix is similar to a Zone, in that it identifies a collection of links which may be accessed as the same next-hop. The Prefix may indicate a single zone, a collection of zones, an entire administrative domain, or a collection of administrative domains. The Prefix is variable in size. The Prefix Size ranges from 1 to 62. The value of 63 cannot be used, since at least 2 bits of the SIP 64-bit identifier are reserved to identify a particular system. Prefix-routed subnet identifiers are supported for addressing globally connected networks in the metropolitan and/or provider addressing models. End-Point Identifiers End-Point identifiers, or any other globally unique identifier, Simpson expires in six months [Page 9] DRAFT system discovery June 1993 may be used with future routing techniques. An End-Point Identifier is indicated as having a Prefix Size of 0. A mobile system may be treated as having an End-Point Identifier when it appears in a prefix-routed subnet, since it will not have the same prefix as other systems in the subnet. Facilities are provided for exchange of redirects and translation between the various forms of identifiers. 3.2. Multicast Support Every SIP system MUST join the all-systems multicast group on all interfaces on which the system supports multicast. Every SIP intermediate-system MUST also join the all-routers multicast group. Every SIP end-system which offers a particular service MUST also join the multicast group for that service. Intermediate-systems do not join the service multicast group, as their services are discovered under a separate process. Simpson expires in six months [Page 10] DRAFT system discovery June 1993 4. Intermediate-System Discovery Before an end-system can send datagrams beyond its directly attached link, it must discover the location of at least one operational intermediate-system on that link. This is accomplished through intermediate-system advertisement messages. The intermediate-system advertisements also serve to indicate zone and subnet prefixes for each link, and to establish neighbor relationships with other intermediate-systems. Each intermediate-system periodically sends the I-Am-Here message to advertise its forwarding capability. End-systems and intermediate- systems discover the location of their neighboring intermediate- systems simply by listening for the advertisements. This eliminates the need for manual configuration of intermediate-system addresses and is independent of any specific routing protocol. The advertisement messages do not constitute a routing protocol, although they might be used by a routing protocol to build a map. They enable systems to discover the existence of neighboring intermediate-systems, but not necessarily which intermediate-system is best to reach a particular destination. If a system chooses a poor intermediate-system for a particular destination, it should receive a redirect from that intermediate-system. However, the advertisements often contain sufficient information to make a good choice of first-hop. This may be important for choosing among intermediate-systems which are participating in a security group or policy-based routing. 4.1. Solicitations Every SIP end-system MUST implement Intermediate-System Solicitation. When any end-system starts up, it MUST send the Where-Are-You solicitation to prompt the advertisement of intermediate-systems. This is also used by the intermediate-systems to construct a map of accessible end-systems, to discover partitions in the local subnet, and to support mobile systems. If (and only if) no advertisements from neighboring intermediate- systems are forthcoming, the end-system MAY retransmit the Where- Are-You a small number of times, but then MUST desist from sending more solicitations. Any intermediate-systems that subsequently start up, or that were not Simpson expires in six months [Page 11] DRAFT system discovery June 1993 discovered because of packet loss or temporary link partitioning, are eventually discovered by reception of their periodic (unsolicited) advertisements. Links that suffer high packet loss rates or frequent partitioning are accommodated by increasing the rate of intermediate-system advertisements, rather than increasing the number of solicitations that end-systems are permitted to send. 4.1.1. Constants MAX_SOLICITATIONS 3 transmissions MAX_SOLICITATION_DELAY 1 second SOLICITATION_INTERVAL 3 seconds 4.1.2. Implementation The intermediate-system solicitation is sent to the all-routers multicast, with the scope set to local. An end-system is required to transmit up to MAX_SOLICITATIONS Where- Are-You messages from any of its interfaces after any of the following events: - The interface is initialized at system startup time. - The interface is reinitialized after a temporary interface failure or after being temporarily disabled by system management. - The system has its forwarding capability turned off by system management. If a system chooses to send a solicitation after one of the above events, it should delay transmission for a random amount of time between 0 and MAX_SOLICITATION_DELAY. This serves to alleviate congestion when many systems start up on a link at the same time, such as might happen after recovery from a power failure. It is recommended that systems include some unique value (such as one of their interface or link-layer identifiers) in the seed used to initialize their pseudo-random number generators. Although the randomization range is specified in units of seconds, the actual randomly-chosen value should not be in units of whole seconds, but rather in units of the highest available timer resolution. The small number of retransmissions of a solicitation, which are Simpson expires in six months [Page 12] DRAFT system discovery June 1993 permitted if no advertisement is received, should be sent at intervals of SOLICITATION_INTERVAL seconds, without further randomization. Upon receiving a valid advertisement from any intermediate-system subsequent to one of the above events, the system MUST NOT send any solicitation on that interface (even if none have been sent yet) until the next time one of the above events occurs. 4.1.3. Receipt An end-system MUST silently discard any received Intermediate-System Solicitation messages. An intermediate-system MUST silently discard any received Intermediate-System Solicitation messages that do not satisfy the following validity checks: - ICMP Checksum is correct. - ICMP length (derived from the payload length) is 16 or more octets. - Source Address is either 0 or the identifier of a neighbor (an identifier that matches one of the intermediate-system's own identifiers on the arrival interface under the prefix mask associated with that identifer, or the zone associated with that interface). 4.2. Advertisements Every SIP intermediate-system MUST implement Intermediate-System Advertisements. The intermediate-system advertisements include such important information as the media address to access the system, other subnets directly accessible through the system, services available through the system, and neighboring intermediate-systems heard. Identifiers Each intermediate-system advertisement includes one or more identifier fields. These indicate the identifiers which are presently in use for each interface of the intermediate-system. Simpson expires in six months [Page 13] DRAFT system discovery June 1993 Zone Each advertised identifier includes a zone field. The value ranges from 0 to 255, and indicates a subnet number which is unique to the administrative domain. A value of zero indicates that no zone number has been assigned. It may be combined with an interface media address to make a locally significant identifier. If all advertised zone values are zero, then zone routing is not available beyond that link. This does not prevent the use of locally significant identifiers for communication with other systems on the local link. Prefix Size Each advertised identifier includes a prefix size field. The value ranges from 0 to 62, and indicates the number of bits in the Identifier which define the prefix mask for the link. A value of zero indicates an end-point identifier. When the value is not zero, the identifier may be used to discern prefix-routed subnet mapping. If all advertised prefix values are zero, then subnet prefix- routing is not in use on that link. Preference Each advertised identifier includes a preference field. This is used to choose a default intermediate-system for the first-hop when the end-system has not yet been redirected or configured to use a specific intermediate-system for a particular destination. The end-system is expected to choose from those intermediate- systems that have the highest preference level for the best prefix-routing match. When there is no match, or prefix-routing is not in use, the preference value is used alone. A network administrator can configure intermediate-system preference levels to encourage or discourage the use of particular intermediate-systems as the default first-hop. The use of separate preferences per prefix allows the choice of different intermediate-systems for each prefix, when there are multiple prefixes in use for the same link. This may be useful where multiple organizations share resources. [I am not sure how this works when there are multiple identifiers per end-system interface.] The preference value is not the same as the "metric" used in many Simpson expires in six months [Page 14] DRAFT system discovery June 1993 routing protocols. It is used only by end-systems in determining the default first-hop, rather than by intermediate-systems in choosing a link for transit traffic. The values are not additive. Therefore, the range of values is smaller, and a higher value indicates a higher preference. It should be understood that preference levels learned from intermediate-system advertisements do not affect any system's cached route entries. For example, if a system has been redirected to use a particular intermediate-system to reach a specific destination, it continues to use that intermediate-system for that destination, even if it discovers another intermediate- system identifier with a higher preference level. Preference levels influence the choice of intermediate-system only for a destination for which there is no cached or configured route, or whose cached route points to an intermediate-system that is subsequently determined to be unreachable. 4.2.1. Constants MAX_INITIAL_ADVERTISEMENTS 3 transmissions MAX_INITIAL_ADVERT_INTERVAL 16 seconds MAX_RESPONSE_DELAY 2 seconds 4.2.2. Configuration An intermediate-system MUST allow the following variables to be configured by system management. Default values are specified which make it unnecessary to re-configure these variables in most cases. For each interface: MaxAdvertisementInterval The maximum time (in seconds) allowed between sending intermediate-system advertisements from the interface. Must be no less than 4 seconds and no greater than 1800 seconds. Default: 600 seconds MinAdvertisementInterval The minimum time (in seconds) allowed between sending unsolicited intermediate-system advertisements from the interface. Must be no Simpson expires in six months [Page 15] DRAFT system discovery June 1993 less than 1 second and no greater than MaxAdvertisementInterval. Default: 0.75 * MaxAdvertisementInterval AdvertisementLifetime The value (in seconds) to be placed in the Lifetime field of intermediate-system advertisements sent from the interface. Must be no less than MaxAdvertisementInterval and no greater than 9000 seconds. Default: 3 * MaxAdvertisementInterval For each of the identifiers of each interface: Advertise A flag indicating whether or not the identifier is to be advertised. Default: TRUE PreferenceLevel The preferability of the interface as a default intermediate- system choice, relative to other intermediate-system interfaces serving the same prefix on the same link. Values are in the range 0 to 255. Higher values mean more preferable. The minimum value 0 is used to indicate that the identifier, even though it may be advertised, is not to be used by neighboring end-systems as a default intermediate-system address. Default: 1 It is useful to configure an identifier with a preference level of 0 (rather than simply setting its Advertise flag to FALSE) when advertisements are being used for "black hole" detection. In particular, an intermediate-system that is to be used to reach only specific destinations could advertise a preference level of 0 (so that neighboring end-systems will not use it as a default intermediate-system for reaching arbitrary destinations) and a non- zero lifetime (so that neighboring end-systems that have been redirected or configured to use it can detect its failure by timing out the reception of its advertisements). It has been suggested that, when the preference level of an Simpson expires in six months [Page 16] DRAFT system discovery June 1993 identifier has not been explicitly configured, an intermediate-system could set it according to the metric of the intermediate-system's "default route" (if it has one), rather than defaulting as suggested above. Thus, an intermediate-system with a better metric for its default route would advertise a higher preference level for its identifier. (Note that routing metrics that are encoded such that "lower is better" would have to be inverted before being used as preference levels in intermediate-system advertisement messages.) Such a strategy might reduce the amount of redirect traffic on some links by making it more likely that an end-system's first choice for reaching an arbitrary destination is also the best choice. On the other hand, redirect traffic is rarely a significant load on a link, and there are some cases where such a strategy would result in more redirect traffic (on links from which the most frequently chosen destinations are best reached via intermediate-systems other than the one with the best default route). Also, since the routing algorithms learn of neighboring intermediate-systems from the advertisements, and the default routes are learned from the routing algorithms, the calculated preference may be unstable from time to time. This document makes no recommendation concerning this issue, and implementors are free to try such a strategy, as long as they also support static configuration of preference levels as specified above. 4.2.3. Implementation The intermediate-system advertisement is sent to the all-systems multicast, with the scope set to local. The term "advertising interface" refers to any functioning and enabled interface that has at least one identifier whose configured Advertise flag is TRUE. From each advertising interface, the system MUST transmit periodic I-Am-Here messages. CONTROVERSIAL: When an intermediate-system discovers that it is receiving its own advertisements, that is an indication that it has more than one interface on same link. The system MUST choose only one advertising interface for each link. Identifiers associated with the remaining interfaces on the same link are indicated with the Other-Identifier extension. Redirect is used to move specific traffic to the alternate interfaces. An intermediate-system MAY proxy for the identifers of other Simpson expires in six months [Page 17] DRAFT system discovery June 1993 systems, using the Other-Identifier extension. This SHOULD only be used when the intermediate-system is translating to another network-layer protocol format. The advertisements are not strictly periodic. The interval between subsequent transmissions is randomized to reduce the probability of synchronization with the advertisements from other intermediate- systems on the same link. This is done by maintaining a separate transmission interval timer for each advertising interface. Each time an advertisement is sent from an interface, that interface's timer is reset to a uniformly-distributed random value between the configured MinAdvertisementInterval and MaxAdvertisementInterval. Expiration of the timer causes the next advertisement to be sent, and a new random value to be chosen. It is recommended that intermediate-systems include some unique value (such as one of their interface or link-layer addresses) in the seed used to initialize their pseudo-random number generators. Although the randomization range is configured in units of seconds, the actual randomly-chosen values should not be in units of whole seconds, but rather in units of the highest available timer resolution. For the first few advertisements sent from an interface (up to MAX_INITIAL_ADVERTISEMENTS), if the randomly chosen interval is greater than MAX_INITIAL_ADVERT_INTERVAL, the timer should be set to MAX_INITIAL_ADVERT_INTERVAL instead. Using this smaller interval for the initial advertisements increases the likelihood of an intermediate-system being discovered quickly when it first becomes available, in the presence of possible packet loss. An interface may become an advertising interface at times other than system startup, as a result of recovery from an interface failure or through actions of system management such as: - enabling the interface, if it had been administratively disabled and it has one or more identifiers whose Advertise flag is TRUE, - enabling SIP forwarding capability (changing the system from an end-system to an intermediate-system), when the interface has one or more identifiers whose Advertise flag is TRUE, - setting the Advertise flag of one or more of the interface's identifiers to TRUE (or adding a new identifier with a TRUE Advertise flag), when previously the interface had no identifier whose Advertise flag was TRUE. In such cases, the intermediate-system must commence transmission of periodic advertisements on the new advertising interface, limiting Simpson expires in six months [Page 18] DRAFT system discovery June 1993 the first few advertisements to intervals no greater than MAX_INITIAL_ADVERT_INTERVAL. In the case of an end-system becoming an intermediate-system, the system must also join the all-routers multicast group on all interfaces on which the intermediate-system supports multicast (whether or not they are advertising interfaces). An interface MAY also cease to be an advertising interface, through actions of system management such as: - shutting down the system, - administratively disabling the interface, - disabling SIP forwarding capability (changing the system from an intermediate-system to an end-system), - setting the Advertise flags of all of the interface's identifiers to FALSE. In such cases, the intermediate-system SHOULD transmit a final multicast advertisement on the interface, identical to its previous transmission, but with a Lifetime field of zero. In the case of an intermediate-system becoming an end-system, the system must also depart from the all-routers multicast group on all interfaces on which the intermediate-system supports multicast (whether or not they had been advertising interfaces). When the Advertise flag of one or more of an interface's identifiers are set to FALSE by system management, but there remain other identifiers on that interface whose Advertise flags are TRUE, the intermediate-system SHOULD send a single multicast advertisement containing only those identifiers whose Advertise flags were set to FALSE, with a Lifetime field of zero. In addition to the periodic unsolicited advertisements, an intermediate-system MUST send advertisements in response to valid advertisements or solicitations received on any of its advertising interfaces. If the advertisement or solicitation does not contain any System-Heard extension, and the time since the previous advertisement is greater than MAX_INITIAL_ADVERT_INTERVAL, the intermediate-system MUST multicast an advertisement from that interface. Whenever these response advertisements are sent, the advertisement MUST be delayed for a small random interval not greater than MAX_RESPONSE_DELAY, in order to prevent synchronization with other responding intermediate-systems, and to allow multiple closely-spaced solicitations to be answered with a single advertisement. The Simpson expires in six months [Page 19] DRAFT system discovery June 1993 interface's interval timer is reset to a new random value, as with unsolicited advertisements. 4.2.4. Receipt All systems MUST silently discard any received Intermediate-System Advertisement messages that do not satisfy the following validity checks: - ICMP Checksum is correct. - ICMP length (derived from the payload length) is 16 or more octets. - At least one Routing-Information extension. - For interfaces which are not point-to-point links, the Media- Access extension. 4.3. Processing Advertisements Every intermediate-system saves the information contained in the advertisements, in order to respond to future requests. Any other action on receipt of such messages by an intermediate-system (for example, as part of a "peer discovery" process) is beyond the scope of this document. An end-system saves the information contained in the advertisements, in order to determine the first-hop when sending datagrams. First- hop determination is elaborated in a subsequent section. 4.3.1. Configuration The Host Requirements -- Communication Layers [1], Section 3.3.1.6, specifies that each end-system must support a configurable list of default intermediate-system identifiers. The purpose of the intermediate-system discovery messages is to eliminate the need to configure that list. On links for which intermediate-system discovery is administratively disabled, it MAY continue to be necessary to configure the default intermediate-system list in each end-system. Each entry in the list contains (at least) the following configurable variables: Simpson expires in six months [Page 20] DRAFT system discovery June 1993 RouterAddress An identifier of a default intermediate-system. Default: (none) PreferenceLevel The preferability of the RouterAddress as a default intermediate- system choice, relative to other intermediate-system interfaces serving the same prefix on the same link. The Host Requirements RFC does not specify how this value is to be encoded. The values used here are defined above. Default: 255 4.3.2. Implementation To process an Intermediate-System Advertisement, an end-system scans the list of Routing-Information extensions contained in it. For each identifier, the end-system does the following: - If the prefix size is not zero, the identifier and prefix size are compared against any identifiers associated with the interface on which the message was received. If there is a match, the interface prefix size is set to the advertised prefix size. - If the identifier is not already present in the end-system's intermediate-system list, a new entry is added to the list, containing the identifier along with its accompanying preference level, and a timer initialized to the Lifetime value from the advertisement. - If the identifier is already present in the end-system's intermediate-system list as a result of a previously-received advertisement, its preference level is updated and its timer is reset to the value in the newly-received advertisement. - If the identifier is already present in the end-system's intermediate-system list as a result of system configuration, no change is made to its preference level. There is no timer associated with a configured identifier. - If a Media-Access extension is present, the intermediate-system list is updated with the location information. Whenever the timer expires in any entry that was created as a result Simpson expires in six months [Page 21] DRAFT system discovery June 1993 of a received advertisement, that entry is discarded. Note that any intermediate-system identifiers acquired from the "Gateway" subfield of the vendor extensions field of a BOOTP packet [11] are considered to be configured identifiers; they are assigned the default preference level of 255, and they do not have an associated timer. Note further that any identifier found in the "giaddr" field of a BOOTP packet [3] identifies a BOOTP forwarder which is not necessarily a SIP intermediate-system; such an identifier should not be installed in the end-system's default intermediate-system list. To limit the storage needed for the default intermediate-system list, an end-system MAY choose not to store all of the intermediate-system identifiers discovered via advertisements. The end-system SHOULD discard those identifiers with lower preference levels in favor of those with higher levels. It is desirable to retain more than one default intermediate-system identifier in the list; if the current choice of default intermediate-system is discovered to be down, the end-system may immediately choose another default intermediate-system without having to wait for the next advertisement to arrive. Any intermediate-system identifier advertised with a preference level of zero is not to be used by the end-system as default intermediate- system identifier. Such an identifier may be omitted from the default intermediate-system list, unless its timer is being use as a "black-hole" detection mechanism. Simpson expires in six months [Page 22] DRAFT system discovery June 1993 5. End-System Discovery Within a directly attached link, each system must be able to locate end-systems with which it desires to communicate. This is accomplished using the Where-Are-You and I-Am-Here messages described below. This is independent of any specific media. When an intermediate-system needs the location of an end-system, it sends the Where-Are-You solicitation. The target end-system responds with the I-Am-Here advertisement. When no intermediate-system advertisements have been heard, an end- system sends the Where-Are-You solicitation itself. The target end- system responds with the I-Am-Here advertisement as usual. When an end-system has heard one or more intermediate-system advertisements, the default behavior is to send all datagrams to the preferred intermediate-system. If the target end-system is accessible on the local link, the intermediate-system sends a redirect back indicating the appropriate media address. When an end-system has heard one or more intermediate-system advertisements, and no zone or prefix-routing is being used, or no prefix matches any current interface identifier, the end-system can assume that it is operating as a mobile end-system. The mobile end- system advertises on a periodic basis, just as an intermediate- system. 5.1. Solicitations Every SIP system MUST implement End-System Solicitation for discovery of local end-systems. When a system is ready to send a datagram to another system, it examines its cache of system locations. If no intermediate-system advertisements have been received, the system MUST send the Where- Are-You solicitation to prompt the advertisement of the target system. If (and only if) no advertisements from the target system are forthcoming, the system MAY retransmit the Where-Are-You a small number of times, but then MUST desist from sending more solicitations. Simpson expires in six months [Page 23] DRAFT system discovery June 1993 5.1.1. Implementation The end-system solicitation is sent to the all-systems multicast. The end-system solicitations use the same configuration constants as intermediate-system solicitations. Unlike intermediate-system solicitations, end-system solicitations are sent only when a particular end-system location is needed, rather than on startup. End-system solicitations are sent using the same periodicity calculations as intermediate-system solicitations. Upon receiving a valid advertisement from any intermediate-system, an end-system MUST NOT send any end-system solicitations. 5.1.2. Receipt An intermediate-system MUST silently discard any received End-System Solicitation messages. An end-system MUST silently discard any received End-System Solicitation messages that do not satisfy the following validity checks: - ICMP Checksum is correct. - ICMP length (derived from the payload length) is 16 or more octets. - Source Address is either 0 or the identifier of a neighbor (an identifier that matches one of the end-system's own identifiers on the arrival interface under the prefix mask associated with that identifer, or the zone associated with that interface). 5.2. Advertisements Every SIP end-system MUST implement End-System Advertisements. Usually, end-system advertisements are sent in response to end-system solicitations. In addition, mobile end-system advertisements and service end-system advertisements (described below) are sent on a periodic basis. The end-system advertisements include such important information as Simpson expires in six months [Page 24] DRAFT system discovery June 1993 the media address to access the system, and neighboring intermediate-systems heard. 5.2.1. Implementation The periodic mobile end-system advertisement is sent to the all- routers multicast. The single end-system advertisement in respnse to a solicitation is sent to the all-systems multicast. In either case, the scope is set to local. CONTROVERIAL: The all-systems multicast is used for end-system advertisements, rather than responding directly to the soliciting system. This is under the assumption that all intermediate- systems need to update the list of active end-systems, when the query is sent by a router. Logically, the response could be sent to all-routers. However, when the query is sent by an end-system, there are no routers present. The response could be sent directly to the requesting end-system. There is no easy way to determine that the sender was an intermediate-system rather than an end-system. The only multicast which covers both cases is all-systems. Mobile advertisements use similar configuration constants and variables as intermediate-system advertisements. Mobile advertisements are sent using the same periodicity calculations as intermediate-system advertisements. Advertising interfaces are established and terminated in the same manner as intermediate-system advertisements. Simpson expires in six months [Page 25] DRAFT system discovery June 1993 6. Service Discovery Each system offering one of the special configuration services detailed below, whether an end-system or intermediate-system, includes that service availability in every advertisement that it sends. All systems discover the location of these services simply by listening for the advertisements. This eliminates the need for manual configuration, periodic probes, and special handling of certain packet types by intermediate-systems. The learned service information is included in any neighboring intermediate-system advertisements. In this fashion, the intermediate-system advertisements provide a summary of all available network services, and pass information beyond the link where the advertisement originated. This results in a reduction of network traffic when compared to the broadcast or multicast of service discovery requests/replies over a wide area. The initial services listed here are primarily concerned with configuration. The locations of other facilities may be learned from these basic servers. Domain Name Service Before a system can communicate with another system, it must learn that system's identifiers and location. The Domain Name System (DNS) is usually used for this purpose. In the past, this was accomplished by reading a list of servers from a (possibly remote) configuration file at startup time. Some systems discovered servers by sending periodic probes to a broadcast or multicast address. Both of these methods have serious drawbacks. Configuration files must be maintained manually (a significant administrative burden when ther are large numbers of systems), and are unable to track dynamic changes in DNS availability. Periodic probes are restricted from using recursion (see Host Requirements -- Application and Support [2], Section 6.1.3.2), and are thus limited to information about the local domain. In practice, only systems which are users or stub resolvers of the DNS can use the DNS server advertisements. Full-Service resolvers MUST continue to be manually configured to ensure a heirarchy of believability within the network. Self-Configuration Service Before a system can communicate with another system, it must learn Simpson expires in six months [Page 26] DRAFT system discovery June 1993 its own identity. The Bootstrap Protocol (BOOTP) is frequently used for this purpose. In the past, this was accomplished by ad hoc passing of BOOTP requests by routers. This method has several serious drawbacks. Presence of the feature cannot be relied upon. It is not of much use for mobile, roving or portable systems. 6.1. Solicitations Every SIP end-system SHOULD implement End-System Solicitation for discovery of local services. When a system is ready to use a particular service, it examines its cache of such services. If no intermediate-system or other service advertisements have been received, the system MAY send the Where- Are-You solicitation to prompt the advertisement of the service. If (and only if) no advertisements from desired services are forthcoming, the system MAY retransmit the Where-Are-You a small number of times, but then MUST desist from sending more solicitations. 6.1.1. Implementation The service solicitation is sent to the special multicast for each particular service, with the scope set to local. The service solicitations use the same configuration constants as intermediate-system and end-system solicitations. Unlike intermediate-system solicitations, service solicitations are sent only when a particular service is utilized, rather than on startup. Service solicitations are sent using the same periodicity calculations as intermediate-system and end-system solicitations. Upon receiving a valid advertisement from any intermediate-system, the system MUST NOT send any service solicitation. Service solicitations require the same validity checks as end-system solicitations. Simpson expires in six months [Page 27] DRAFT system discovery June 1993 6.2. Advertisements Like intermediate-system and mobile end-system advertisements, service end-systems advertisements are sent on a periodic basis. Services offered by intermediate-systems are included in the intermediate-system advertisements described above. 6.2.1. Implementation The service advertisement is sent to the all-systems multicast, with the scope set to local. CONTROVERIAL: The all-systems multicast is used for service advertisements, rather than different multicasts for each service. This is under the assumption that all systems need to learn of services. This corresponds to the design for intermediate-system advertisements. Thus, intermediate-system advertisements can be viewed as a special case of service advertisements. This ensures that the design will operate when there are no routers, and when the routing protocols are still initializing. The service advertisements use similar configuration constants and variables as intermediate-system advertisements. Service advertisements are sent using the same periodicity calculations as intermediate-system advertisements. Advertising interfaces are established and terminated in the same manner as intermediate-system advertisements. When any system ceases to offer an advertised service, the system SHOULD transmit a final multicast advertisement on the interface, identical to its previous transmission, but with a Lifetime field of zero. Simpson expires in six months [Page 28] DRAFT system discovery June 1993 7. Self Discovery 7.1. End-Systems At startup, each SIP end-system solicits the advertisements of intermediate-systems, as described in Intermediate-System Discovery above. Until an intermediate-system is discovered, an end-system is limited to accessing systems and services for the links to which it is directly attached. In the absence of an intermediate-system, each SIP end-system solicits the advertisements of services as described in Service Discovery above. Until self-configuration services are discovered, an end-system is limited to accessing systems and services according to prior configuration. 7.1.1. Zone Determination Until an intermediate-system is discovered, an end-system assumes a zone number of zero. When combined with any IEEE-802 number found in the machine, or other identifier negotiated at the link level, this yields a local identifier which is unique to the system. When an intermediate-system is discovered, the advertisements are examined for zone information, as described in Intermediate-System Discovery above. If all advertised zone values are zero, then zone routing is not available beyond that link. If more than one zone number is discovered for the same interface, only the highest zone number is used. When there is more than one interface on a multi-homed end-system, each interface MUST answer to all of the local identifers generated. When more than one IEEE-802 number is available, the primary system identifier is composed of the highest zone discovered, combined with the highest IEEE-802 number found. 7.1.2. Initialization Once a system has becomed locally addressable, it can engage in exchanges with local servers. Some of these local servers could be a bootstrap service, for loading and configuring the system. Another server could be a registration service, in charge of managing the local name and identifier space. Simpson expires in six months [Page 29] DRAFT system discovery June 1993 When the registration service is unable to find a match for the system, the system SHOULD request the operator to provide a name for the system. The registration service would be responsible for ensuring uniqueness, and assigning appropriate identifiers for the name. Further specification of such services is beyond the scope of this document. 7.1.3. Identifier Determination Once the Domain Name has been determined for a system, the Domain Name Service SHOULD be consulted to determine the globally advertised identifiers for the system. In this fashion, system is coordinated with the most current information actually propagated within the internet. Each DNS identifier has a Time-To-Live associated with it. When any identifier expires, another request SHOULD be made to the DNS for a list of identifiers. When there is more than one interface on a multi-homed end-system, each interface MUST answer to all of the identifers learned. When more than one identifier is returned for a system, the primary system identifier is the identifier with the highest TTL, or the first listed identifier of those with the highest TTL. 7.1.4. Prefix Determination The prefix size is dynamically learned from matching interface identifiers against the intermediate-system advertisements, as described in Intermediate-System Discovery above. Unlike previous practice, an end-system prefix sizes SHOULD NOT be preconfigured. Any preconfigured value MUST be superceded by new values and changes propagated in intermediate-system advertisements. 7.1.5. Changing Identifiers 7.2. Intermediate-Systems The zones and prefixes are assigned by hand. Simpson expires in six months [Page 30] DRAFT system discovery June 1993 8. Next-Hop Determination When an end-system has not heard any intermediate-system advertisements, it is assumed that all end-systems are only accessible on the local link. multi-homed preferred router smart selection local redirect remote redirect Simpson expires in six months [Page 31] DRAFT system discovery June 1993 8.1. Examples of Use Simple case -- J to K on the same fully-connected link. J sends the Where-Are-You (which contains its own media address) to all-systems. K sends the I-Am-Here (which contains its own media address) directly to all-systems. At this point, they both know that they can talk directly to each other, without regard to subnet. Routed case -- J to K not on the same fully-connected link. If no resource reservation or policy routing is desired, J simply sends its packets directly to the "preferred" router that it has learned from the Advertisements. If there is a better router for the first-hop, that router sends the I-Am-Here redirect to J, but never-the-less forwards the packet. In the presence of RR or PR, J sends a Where-Are-You to the "preferred" router that it has learned from the Advertisements. That router always returns an I-Am-Here redirect (even if the correct hop is itself), which contains the requested RR or PR status information. J then sends its packets to the first-hop router as determined from the I-Am-Here. General case -- J to K over disconnected partial mesh (radio/framerelay). J periodically sends the I-Am-Here (which contains its own media address, and the addresses of its "heard" routers) to the all-routers multicast. The routers use such messages to construct a map of the current state of the topology. The routers now know who J hears, and who hears J. If the routing map doesn't contain a current whereabouts of K, the Destination Unreachable message is returned by the "best" router on J's "heard" list. If the routing map contains the current whereabouts of K, the "best" router on K's "heard" list sends a Where-Are-You to K, with a list of routers which can hear K. The list is ordered by the intersection of those routers which can also hear J, minimizing the number of hops. When K hears the Where-Are-You, it sends the I-Am-Here to the all-systems address. The "best" router on J's "heard" list sends an I-Am-Here redirect to J, with a substitute list of routers which can hear J. The list is ordered by the intersection of those routers which can also hear K. Simpson expires in six months [Page 32] DRAFT system discovery June 1993 Of course, J may have heard K's I-Am-Here directly. At this point, the routing fabric knows which routers are heard by J and K, and which routers can hear J and K. J and K know whether they can hear each other directly. If not, they know the "best" next-hop router (which may not be the same in both directions). Unlike the fully-connected scenarios, this scheme requires that the I-Am-Here is sent from time to time to keep the map updated. However, only routers need store the information. Simpson expires in six months [Page 33] DRAFT system discovery June 1993 9. Additional ICMP Packets The Packet format and basic facilities are already defined for ICMP [3], as modified for SIP [1]. Up-to-date values of the ICMP Type field are specified in the most recent "Assigned Numbers" RFC [2]. This document concerns the following values: Where-Are-You I-Am-Here Simpson expires in six months [Page 34] DRAFT system discovery June 1993 9.1. Where-Are-You A summary of the Where-Are-You message format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Code | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + System Identifier + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Extensions ... +-+-+-+-+-+-+-+-+-+-+-+-+ Type Code The Code field is one octet. Up-to-date values of the I-Am-Here Code field are specified in the most recent "Assigned Numbers" RFC [2]. Current values are assigned as follows: 0 RESERVED 1 End-System Solicitation 2 Intermediate-System Solicitation Checksum The ICMP Checksum. System Identifier The System Identifier field is eight octets in length, and contains an identifier of the system which is sought. When the identifer of the system is unknown, the field is zero filled. Extensions The Extensions field is variable in length and contains zero or Simpson expires in six months [Page 35] DRAFT system discovery June 1993 more Extensions. These Extensions are described in a later section. The contents of the Reserved field are ignored. Future backward- compatible changes to the protocol may specify the contents of the Reserved field or of additional octets at the end of the message. Simpson expires in six months [Page 36] DRAFT system discovery June 1993 9.1.1. End-System Solicitation The End-System Solicitation contains the following values: - In the Destination Address field of the SIP header: For service solicitations, the special multicast group associated with the service. For other solicitations, the all-systems multicast. In either case, the scope is set to local. - In the Source Address field of the SIP header: any identifier associated with the sending interface. It MAY contain zero if the system has not yet determined an identifier for the interface. - In the Code field of the ICMP header: 1 for End-System Solicitation. - For each intermediate-system advertisement that has been heard, the System-Heard extension. - For interfaces which are not point-to-point links, the Media- Access extension. In the unlikely event that not all extensions fit in a single solicitaion, as constrained by the MTU of the link, the remaining extensions are removed. Only a single solicitation is sent. Simpson expires in six months [Page 37] DRAFT system discovery June 1993 9.1.2. Intermediate-System Solicitation The Intermediate-System Solicitation contains the following values: - In the Destination Address field of the SIP header: the all- routers multicast, with the scope set to local. - In the Source Address field of the SIP header: any identifier associated with the sending interface. It MAY contain zero if the system has not yet determined an identifier for the interface. - In the Code field of the ICMP header: 2 for Intermediate-System Solicitation. - For each of that system's interface identifiers other than the primary identifier, the Other-Identifier extension, with the prefix size set to zero. - For each intermediate-system advertisement that has been heard, the System-Heard extension. - For interfaces which are not point-to-point links, the Media- Access extension. In the unlikely event that not all extensions fit in a single solicitaion, as constrained by the MTU of the link, multiple solicitations are sent, with each except the last containing as many extensions as can fit. Simpson expires in six months [Page 38] DRAFT system discovery June 1993 9.2. I-Am-Here A summary of the I-Am-Here message format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Code | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | LifeTime | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + System Identifier + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Extensions ... +-+-+-+-+-+-+-+-+-+-+-+-+ Type Code The Code field is one octet. Up-to-date values of the I-Am-Here Code field are specified in the most recent "Assigned Numbers" RFC [2]. Current values are assigned as follows: 0 RESERVED 1 End-System Advertisement 2 Intermediate-System Advertisement 3 Local Redirect 4 Remote Redirect Checksum The ICMP Checksum. Sequence Number The Sequence Number field is two octets in length, and contains the number of I-Am-Here messsages sent since the system was initialized. This number MUST include this advertisement. Simpson expires in six months [Page 39] DRAFT system discovery June 1993 LifeTime The LifeTime field is two octets in length, and indicates the seconds remaining before the entry is considered invalid. System Identifier The System Identifier field is eight octets in length, and contains the primary identifier for this system. Other identifiers are indicated with the Other-Identifier extension. Extensions The Extensions field is variable in length and contains zero or more Extensions. These Extensions are described in a later section. Simpson expires in six months [Page 40] DRAFT system discovery June 1993 9.2.1. End-System Advertisement The End-System Advertisement contains the following values: - In the Destination Address field of the SIP header: For periodic mobile end-system advertisements, the all-routers multicast. For other end-system advertisements, the all-systems multicast. In either case, the scope is set to local. - In the Source Address field of the SIP header: For service advertisements, the primary identifier associated with that system. For responses to solicitations, the identifier specified in the solicitation. - In the Code field of the ICMP header: 1 for End-System Advertisement. - In the Lifetime field: the interface's configured AdvertisementLifetime. - For each of that system's interface identifiers other than the primary identifier, the Other-Identifier extension, with the prefix size set to zero. - For each service advertisement that is offered, the Service- Information extension. - For each intermediate-system advertisement that has been heard, the System-Heard extension. - For interfaces which are not point-to-point links, the Media- Access extension. In the unlikely event that not all extensions fit in a single advertisement, as constrained by the MTU of the link, multiple advertisements are sent, with each except the last containing as many extensions as can fit. Simpson expires in six months [Page 41] DRAFT system discovery June 1993 9.2.2. Intermediate-System Advertisement The Intermediate-System Advertisement contains the following values: - In the Destination Address field of the SIP header: the all- systems multicast, with the scope set to local. - In the Source Address field of the SIP header: the primary identifier of the system. The same identifier is used for all interfaces. - In the Code field of the ICMP header: 2 for Intermediate-System Advertisement. - In the Lifetime field: the interface's configured AdvertisementLifetime. - For each of that interface's identifiers whose Advertise flags are TRUE, the Routing-Information extension. - For each of that interface's recently changed identifiers, the Change-Identifier extension. - For each of that system's other interface's identifiers which have not already been included through prefix subsumption, the Other- Identifier extension. - For each service that is offered, or has been learned from another advertisement, the Service-Information extension. - For each intermediate-system advertisement that has been heard, the System-Heard extension. - For interfaces which are not point-to-point links, the Media- Access extension. In the unlikely event that not all extensions fit in a single advertisement, as constrained by the MTU of the link, multiple advertisements are sent, with each except the last containing as many extensions as can fit. Simpson expires in six months [Page 42] DRAFT system discovery June 1993 10. Extensions Extensions allow variable amounts of information to be carried within each Advertisement or Advertisement packet. Some extensions are common to both packet types. The end of the list of Extensions is indicated by the Payload Length of the SIP packet. A summary of the Extensions format is shown below. The fields are transmitted from left to right. 0 1 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Data ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type The Type field is one octet and indicates the type of Extension. Up-to-date values of the Extension Type field are specified in the most recent "Assigned Numbers" RFC [2]. Current values are assigned as follows: 1 Media-Access 2 Change-Identifier 3 Other-Identifier 4 System-Heard 5 Routing-Information 6 Service-Information 7 Transit-Information 8 Authentication 9 Security-Information 10 Redirected-Header Length The Length field is one octet and indicates the length of the Data field which has been used. Each Extension ends on an octet boundary which is an integral multiple of four octets. Any unused portion of the Data field is padded with zeros. Simpson expires in six months [Page 43] DRAFT system discovery June 1993 length actual 0 through 2 4 3 through 6 8 7 through 10 12 Data The Data field is zero or more octets and contains the value or other information for this Extension. The format and length of the Data field is determined by the Type and Length fields. Simpson expires in six months [Page 44] DRAFT system discovery June 1993 10.1. Media-Access A summary of the Media-Access extension format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Media Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MAC Address ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 1 Length >= 3 Media Type The Media Type field is two octets in length. The value of this field is the same as the Hardware Type used in ARP. Up-to-date values of the Hardware Type field are specified in the most recent "Assigned Numbers" RFC [2]. [Should we use the ifType from MIB-II instead?] MAC Address The MAC Address field is variable in length, and contains the media address which is used to access this system. The MAC Address is always specified in Canonical order. The Media-Access extension MUST be included in those messages sent from an interface on a multi-access media. It MUST NOT be included in a message sent from a point-to-point interface, or in messages such as the Remote Redirect which pass through intermediate systems. Simpson expires in six months [Page 45] DRAFT system discovery June 1993 10.2. Change-Identifier A summary of the Change-Identifier extension format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | |Prefix Size| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + Old Identifier + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + New Identifier + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 2 Length 22 Prefix Size The Prefix Size field is six bits in length, and indicates the number of bits in both Identifiers which define the prefix mask for the link. The value ranges from 0 to 62. End-Systems MUST have a Prefix Size of zero. Old Identifier The Old Identifier field is eight octets in length, and contains the old identifier for this interface. New Identifier The New Identifier field is eight octets in length, and contains one of the identifiers for this interface. This may be another identifier for the same interface that sent the message, or may Simpson expires in six months [Page 46] DRAFT system discovery June 1993 identify another interface on the same system which sent the message. Simpson expires in six months [Page 47] DRAFT system discovery June 1993 10.3. Other-Identifier A summary of the Other-Identifier extension format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | |Prefix Size| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + Interface Identifier + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 3 Length 14 Prefix Size The Prefix Size field is six bits in length, and indicates the number of bits in the Interface Identifier which define the prefix mask for the link. The value ranges from 0 to 62. If the Interface Identifier does not indicate a valid prefix, the value is zero. End-Systems MUST have a Prefix Size of zero. Metric The Metric field is four octets in length, and indicates the preference level for use of this system to forward packets to the Interface Identifier. Lower values indicate greater preference. End-Systems MUST set this field to zero. Interface Identifier The Interface Identifier field is eight octets in length, and Simpson expires in six months [Page 48] DRAFT system discovery June 1993 contains one of the identifiers for this system. This may be another identifier for the same interface that sent the message, or may identify another interface on the same system which sent the message. Every identifier for every interface is listed in each I-Am-Here message. This supports multiple identifiers per interface, as well as multi-homed systems. When a number of interfaces, such as point-to-point interfaces, may be aggregated with the same prefix, only one extension need be included. This enables end-systems to determine the best next-hop without sending a Where-Are-You solicitation when the next-hop is on another interface attached to the same advertising system. Simpson expires in six months [Page 49] DRAFT system discovery June 1993 10.4. System-Heard A summary of the System-Heard extension format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Speed |D|B|Prefix Size| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MRU | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + System Identifier + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | Remaining LifeTime | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Quality | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertisement Count | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Error Count | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 4 Length 30 Designated Bit The Designated Bit indicates that the System Identifier is the Designated Router. Backup Bit The Backup Bit indicates that the System Identifier is the Backup Designated Router. Prefix Size The Prefix Size field is six bits in length, and indicates the number of bits in the System Identifier which define the prefix mask for the Simpson expires in six months [Page 50] DRAFT system discovery June 1993 link. The value ranges from 0 to 62. If the System Identifier does not indicate a valid prefix, the value is zero. End-Systems MUST have a Prefix Size of zero. MRU The Maximum Receive Unit field is two octets in length, and indicates the maximum size packet that the system will receive over the link. Speed The Speed field is one octet in length, and indicates the speed of the link over which the advertisement or solicitation was heard. Higher values indicate greater speed. The speed value is related to int( 10 * ln( speed / 100 ) ) in bits per second. After considerable trial and error, this formula was used because it gave the best distribution for distinguishing medium speed links, and fit reasonably well in the realm of currently envisioned speeds. It has an upper limit of 11.87 Terabits per second. (It also has a convenient button on the calculator.) 0 link is down 1 - 9 reserved 10 300 or less 24 1,200 96 1,544,000 T1 31 2,400 99 2,048,000 E1 38 4,800 106 4,000,000 Token Ring 42 7,200 110 6,312,000 T2 45 9,600 115 10,000,000 Ethernet 49 14,400 119 16,000,000 Token Ring 52 19,200 56 28,800 130 44,736,000 T3 59 38,400 142 155,520,000 STS-3,STM-1 63 57,600 202 622,080,000 STS-12,STM-4 64 64,000 216 2,488,320,000 STS-48,STM-16 71 128,000 73 153,600 78 256,000 System Identifier The System Identifier field is eight octets in length, and contains the primary identifier for the system, taken from the Source Address Simpson expires in six months [Page 51] DRAFT system discovery June 1993 field of the advertisement heard. Sequence Number The Sequence Number field is two octets in length, and contains the last heard sequence number from the system. Remaining LifeTime The Remaining LifeTime field is two octets in length, and indicates the seconds remaining before the entry is considered invalid. Quality The Quality field is four octets in length, and contains an indication of the signal quality received from this system. Higher values indicate greater quality. Advertisement Count The Advertisement Count field is four octets in length, and indicates the number of advertisements that have been heard from the identified system. Error Count The Error Count field is four octets in length, and indicates the number of errors which have been detected on the link with the identified system. This extension is included in every I-Am-Here. Simpson expires in six months [Page 52] DRAFT system discovery June 1993 10.5. Routing-Information A summary of the Routing-Information extension format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Preference |D|B|Prefix Size| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MRU | Zone | Priority | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + Interface Identifier + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 5 Length 14 Preference The Preference field is one octet in length, and indicates the preference level for use of this system to forward packets to the Interface Identifier. Higher values indicate greater preference. Designated Bit The Designated Bit indicates that the system is the Designated Router. Backup Bit The Backup Bit indicates that the system is the Backup Designated Router. Prefix Size The Prefix Size field is six bits in length, and indicates the number of bits in the Interface Identifier which define the prefix mask for the link. The value ranges from 0 to 62. Simpson expires in six months [Page 53] DRAFT system discovery June 1993 If the Interface Identifier does not indicate a valid prefix, the value is zero. MRU The Maximum Receive Unit field is two octets in length, and indicates the maximum size packet that the system will receive over the link. Zone The Zone field is one octet in length, and indicates the zone for the link. A value of zero indicates that no zone has been assigned. Priority The Priority field is one octet in length, and indicates the priority for election to Designated Backup. A value of zero indicates that the system is not eligible. Interface Identifier The Interface Identifier field is eight octets in length, and contains one of the identifiers for this interface. This extension is sent only by Intermediate-Systems. When more than one of these extensions is present, the Designated and Backup bits, MRU, Zone and Priority fields MUST be the same in each copy. Simpson expires in six months [Page 54] DRAFT system discovery June 1993 10.6. Service-Information A summary of the Service-Information extension format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Service | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | Remaining LifeTime | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + System Identifier + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Data ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 6 Length >= 14 Service The Service field is two octets in length. The value of this field is usually the same as the well-known port number. Up-to-date values of the Service field are specified in the most recent "Assigned Numbers" RFC [2]. Sequence Number The Sequence Number field is two octets in length, and contains the last heard sequence number from the system. Remaining LifeTime The Remaining LifeTime field is two octets in length, and indicates the seconds remaining before the entry is considered invalid. System Identifier The System Identifier field is eight octets in length, and contains Simpson expires in six months [Page 55] DRAFT system discovery June 1993 the primary identifier for this system. Data The Data field is variable in length, and contains information specific to the service. For example, it could contain a string with the description of the service. The format of the Data field is entirely service dependent, and is always treated as a binary value. Simpson expires in six months [Page 56] DRAFT system discovery June 1993 10.7. Transit-Information A summary of the Transit-Information extension format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | | QoS | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 7 Length 6 QoS The Quality of Service field is one octet in length, and indicates a service for which transit will be accepted. Metric The Metric field is four octets in length, and indicates the preference level for use of this network link to forward packets of the indicated Quality of Service. Lower values indicate greater preference. This extension is included in the Intermediate-System I-Am-Here to indicate that it will accept transit traffic. If this extension is not included, other intermediate-systems will treat the link as a stub network. Simpson expires in six months [Page 57] DRAFT system discovery June 1993 10.8. Authentication A summary of the Authentication extension format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Data ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 8 Length 22 Data The Data field is variable in length, and contains information specific to the authentication method, This extension is included in any I-Am-Here. Simpson expires in six months [Page 58] DRAFT system discovery June 1993 10.9. Security-Information A summary of the Security-Information extension format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Compartments ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 9 Length 22 Compartments The Compartments field is sixteen octets in length. This extension is included in the Intermediate-System I-Am-Here to indicate that it will accept transit traffic for the designated security compartments. Simpson expires in six months [Page 59] DRAFT system discovery June 1993 10.10. Redirected-Header A summary of the Redirected-Header extension format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SIP Header ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 10 Length 22 SIP Header The SIP Header field is 48 octets in length. This extension is included in the Local or Remote Redirect to verifiy the traffic that is being redirected. Simpson expires in six months [Page 60] DRAFT system discovery June 1993 Security Considerations References [1] [2] Acknowledgments Chair's Address The working group can be contacted via the current chairs: Author's Address Questions about this memo can also be directed to: William Allen Simpson Daydreamer Computer Systems Consulting Services P O Box 6205 East Lansing, MI 48826-6205 EMail: Bill.Simpson@um.cc.umich.edu Simpson expires in six months [Page 61] DRAFT system discovery June 1993 Table of Contents 1. Terminology ........................................... 1 2. Criteria .............................................. 2 3. Design Overview ....................................... 8 3.1 System Identification ........................... 9 3.2 Multicast Support ............................... 10 4. Intermediate-System Discovery ......................... 11 4.1 Solicitations ................................... 11 4.1.1 Constants ....................................... 12 4.1.2 Implementation .................................. 12 4.1.3 Receipt ......................................... 13 4.2 Advertisements .................................. 13 4.2.1 Constants ....................................... 15 4.2.2 Configuration ................................... 15 4.2.3 Implementation .................................. 17 4.2.4 Receipt ......................................... 20 4.3 Processing Advertisements ....................... 20 4.3.1 Configuration ................................... 20 4.3.2 Implementation .................................. 21 5. End-System Discovery .................................. 23 5.1 Solicitations ................................... 23 5.1.1 Implementation .................................. 24 5.1.2 Receipt ......................................... 24 5.2 Advertisements .................................. 24 5.2.1 Implementation .................................. 25 6. Service Discovery ..................................... 26 6.1 Solicitations ................................... 27 6.1.1 Implementation .................................. 27 6.2 Advertisements .................................. 28 6.2.1 Implementation .................................. 28 7. Self Discovery ........................................ 29 7.1 End-Systems ..................................... 29 7.1.1 Zone Determination .............................. 29 7.1.2 Initialization .................................. 29 7.1.3 Identifier Determination ........................ 30 7.1.4 Prefix Determination ............................ 30 7.1.5 Changing Identifiers ............................ 30 7.2 Intermediate-Systems ............................ 30 8. Next-Hop Determination ................................ 31 Simpson expires in six months [Page ii] DRAFT system discovery June 1993 8.1 Examples of Use ................................. 32 9. Additional ICMP Packets ............................... 34 9.1 Where-Are-You ................................... 35 9.1.1 End-System Solicitation ......................... 37 9.1.2 Intermediate-System Solicitation ................ 38 9.2 I-Am-Here ....................................... 39 9.2.1 End-System Advertisement ........................ 41 9.2.2 Intermediate-System Advertisement ............... 42 10. Extensions ............................................ 43 10.1 Media-Access .................................... 45 10.2 Change-Identifier ............................... 46 10.3 Other-Identifier ................................ 48 10.4 System-Heard .................................... 50 10.5 Routing-Information ............................. 53 10.6 Service-Information ............................. 55 10.7 Transit-Information ............................. 57 10.8 Authentication .................................. 58 10.9 Security-Information ............................ 59 10.10 Redirected-Header ............................... 60 SECURITY CONSIDERATIONS ...................................... 61 REFERENCES ................................................... 61 ACKNOWLEDGEMENTS ............................................. 61 CHAIR'S ADDRESS .............................................. 61 AUTHOR'S ADDRESS ............................................. 61